Dishwasher Error Codes
73 verified codes. Every page shows the meaning, implicated component, ranked fixes, and the source it was derived from.
- Bosch E01 — A fault in the heating or pump-control circuit was detected.
- Bosch E02 — A water-heating relay fault was detected.
- Bosch E03 — The auxiliary heater relay is faulty.
- Bosch E04 — A fault was detected in the water inlet system.
- Bosch E05 — A malfunction was detected in the circulation system.
- Bosch E09 — The heating element or heat pump is faulty.
- Bosch E12 — A water leak was detected.
- Bosch E14 — A fault was detected in the door latch mechanism.
- Bosch E15 — Leak protection triggered after water was detected in the base pan.
- Bosch E17 — A water inlet valve fault was detected.
- Bosch E18 — A drainage system fault was detected.
- Bosch E22 — The filter or circulation pump is restricted or faulty.
- Bosch E23 — A heating element fault was detected.
- Bosch E24 — The drain pump is blocked or faulty.
- Bosch E25 — A blockage was detected in the drain system.
- Bosch E26 — A main control board fault was detected.
- Bosch E27 — A sensor or valve fault was detected.
- Bosch H01 — A door latch error was detected.
- Frigidaire CE — A communication or configuration fault between the control panel and main board
- Frigidaire CL — The door is open or not securely closed.
- Frigidaire HO — Heat delay or heater-on mode is active.
- Frigidaire I10 — A water inlet fault was detected during fill.
- Frigidaire I20 — The unit did not drain completely.
- Frigidaire I30 — An overflow condition was detected.
- Frigidaire I40 — The filter or sump is clogged.
- Frigidaire I50 — A wash motor fault was detected.
- Frigidaire IC0 — A communication fault was detected in the control electronics.
- Frigidaire IF0 — A water inlet fault was detected.
- Frigidaire LO — A low water level was signaled.
- Frigidaire LOC — The door lock indicator is active.
- Frigidaire PF — A power loss occurred.
- Frigidaire RA — A rinse-aid dispenser fault was detected.
- Frigidaire RE — A temperature probe fault was detected.
- Frigidaire TU — A turbidity sensor fault was detected.
- Frigidaire UO — A drain fault was detected.
- GE 999 — A possible leak was detected or a control reset is needed.
- GE C1 — The drain pump-out exceeded two minutes.
- GE C2 — The total pump-out cycle exceeded seven minutes.
- GE C3 — The dishwasher will not drain.
- GE C4 — The unit refilled twice after a power loss, suggesting a stuck or failed float s
- GE C5 — The pump-out time was too short.
- GE C6 — The incoming water temperature is too low.
- GE C7 — The water-temperature sensor circuit is inoperative.
- GE C8 — The detergent cup is blocked from opening fully.
- GE F56 — The dishwasher failed to drain.
- GE H2O — A low incoming-water condition was detected.
- GE PF — A power failure occurred.
- GE PRS — The pressure sensor is sending an invalid signal.
- LG BE — Excess suds formed from the wrong detergent or an unlevel installation.
- LG CL — The child-lock or control-lock feature is engaged.
- LG E1 — Overfill or leak protection was triggered by the flow switch.
- LG FE — The tub filled beyond the safe level and drained automatically.
- LG HE — A water-heating fault was detected.
- LG IE — Insufficient water reached the tub within the fill window.
- LG LE — A drive-motor fault or wiring-harness problem was detected.
- LG NE — The vario motor that diverts water to the spray arms is faulty.
- LG OE — The tub did not empty properly during the drain phase.
- LG PF — A power failure occurred during the cycle.
- LG TE — Water temperature exceeded the safe limit or the thermistor is faulty.
- Samsung 1E — A clogged filter (Waterwall models) or heater over-temperature (Rotary models),
- Samsung 3C — A drain-pump operation fault was detected.
- Samsung 3E — Incoming water is hotter than the allowed limit.
- Samsung 4C — The water supply is inadequate in pressure or temperature.
- Samsung 5C — The dishwasher cannot drain.
- Samsung 7E — The Waterwall reflector is not moving correctly.
- Samsung 9E — The water level inside the tub is too low.
- Samsung BE — A panel button is being sensed as stuck.
- Samsung CE — A communication fault occurred in the control electronics.
- Samsung HC — The water overheated beyond the safe limit.
- Samsung HE — The heater temperature-detection circuit is faulty.
- Samsung LC — The leak sensor detected moisture.
- Samsung OC — The water level is above the allowed maximum.
- Samsung TE — The temperature sensor is reading incorrectly.